YnHub Guide

$Usercommands

Here you will find some usercommands your can have in your hub.
Look in the setup on this page and take a look at step 14 then these commands will fit the profile.

Install help

Troubleshoot

I have changed so the register part looks much better.
But you will still get the normal reg PM from the bot.

You are now registered, please login with this name & password and add this hub to your favorites
«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»
• Hub name          : <hubname>
• Hub address      : <hubaddress>
• Your nick          : %[line:nick]
• Your password : %[line:Password]
• Your profile       : %[line:Profile]
«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»«»
Don't give it to someone else or your privileges will be taken away!

Admin 1.6

Admin 1.7 (Announce)

No specific profiles

Description

This is the same as the announce command except i have removed all the !say commands, so it will be silent in mainchat. =)

This command uses the !say command each time you register user, Block user, Mainchat on/off and timebans a user.
With a little message in the mainchat to let your users to know what you are doing.

OP 1.6

OP 1.6 (Announce)

No specific profiles

Description

These commands are the same as above. I have only removed the Settings/Texfiles commands.

These commands are the same as above. I have only removed the Settings/Texfiles commands

V.I.P 1.1

Description

Some basic V.I.P commands you can use.
Just look at this picture here so you can add the correct commands for this profile, or just check the setup page,
step 14 and it will get correct.

To the top

Install usercommands
Well you can install the usercommands in a couple of deferent ways. I will try and explain here

Use it as a trigger
Just copy and paste the content in the content box then choose a name for it. Ex Admin.
Enable text command =

Enable when muted =

Min /Max access level = Set this to whatever you have chosen in profiles for the specific account.
Min/Max receive level = This can´t be changed, when broadcast is set to The one writing. so leave this..
Broadcast to = The one writing
Parameters = No parameter
Edit level = Set this to 10
Schedule = 0
Command visibility = Set this to whatever you want but i prefer Nobody on this
Message type = Raw command
Autorun = None
Then hit the "save as" button, then get into the hub and try it out just type +admin in mainchat

Autosend the command
Copy and paste it into the content box and choose a name for it. ex admin-commands.
Enable text command =

Enable when muted =

Min/Max access-level = Set this to whatever you have chosen in profiles.
Min/Max receive level = This can´t be changed, when broadcast is set to The one writing. so leave this.
Broadcast to = The one writing
Parameters = No parameter
Edit level = 10
Schedule = 0
Command visibility = I prefer Nobody
Message type = Raw command
Autorun = OnLogin
Now you don´t need to type anything to get the commands, you will get them automatically when you log in

To the top

Troubleshoot

My commands ain't working, can only get them with +command.name.
Well i have got allot of email about this, and it´s simple.
Remove or edit the level for the textcommand that is called UserCommands in YnHub, This command simply erases my commands, so change the level of it or remove it.

Everyone gets my command when they log in.
Change the Min/Max level on the text command and set it to a higher level then your ordinary users. Just remember not to set it to a higher level then yourself.

How do i know which level my OP´s have?
Look in Profiles in the GUI and mark the OP profile, right under the name box you will se a bar that looks like this

Every-time anyone logs in, i get the commands sent to me again.
Change "broadcast to". it should say "The one writing"

Why can´t i edit my commands through the hubcommands?
You need to set the correct edit level, should be the same as Min/Max receive/access level if you want to edit it through the hubcommands

How come everyone can se the + command but not the ! command?
Change the command visibility to "nobody" or the "one writing". To change the integrated command go to Miscellaneous and change hub command visibility to "nobody" and the same for integrated command

Why can´t i see the account in profiles, i don't get the PM from the bot at all saying the user is registered.
You have to get to Profiles then click the user tab. Mark "add account"

To the top